Snaking punches a hole through a clog, and hydro jetting washes the inside of the pipe clean with high-pressure water. Snaking suits a simple blockage in one drain, while jetting suits grease, sludge, roots and clogs that keep coming back. Call the number on this page to be connected with an independent local plumber who can tell you which fits.
When a drain stops, plumbers usually offer one of two cleanings. They sound similar, but they do different jobs, cost different amounts, and suit different pipes. Here is how to tell them apart and which one to ask about.
How drain snaking works
A drain snake, also called an auger, is a long, flexible cable with a cutting or hooked head that spins as it is fed into the pipe. It either breaks the clog apart or hooks it so it can be pulled out. Homeowners use hand-crank versions for sinks, and plumbers use motorized machines that reach much farther down a main line. Snaking is quick, works well on a hair clog, a single wad of paper or a toy that went down a toilet, and is the usual first move. The limit is that a cable cuts a channel through the blockage but does not scrub the pipe wall, so grease and sludge can remain and rebuild.
How hydro jetting works
Hydro jetting feeds a hose with a specialized nozzle into the pipe and sends water out at very high pressure. The jets point backward to pull the hose forward and spray forward and sideways to scour the walls. It removes grease, soap scum, mineral buildup and silt, and it can cut through some tree roots. Because it cleans the entire inside of the pipe rather than one blockage, results tend to last longer. A good plumber runs a camera first, so you know what the jets will meet. A hydro jetting visit needs a cleanout or access point, and the water and debris have to flow somewhere, so it is not a casual do-it-yourself job.
Side by side
| Question | Snaking | Hydro jetting |
|---|---|---|
| What it does | Breaks up or pulls out a clog | Scours the entire pipe wall |
| Best for | Single fixture clogs, hair, paper, small blockages | Grease, sludge, mineral scale, roots, recurring main line clogs |
| Typical cost | About $100 to $300, up to $500 for a main line | About $350 to $600 or more |
| How long it lasts | Often needs repeating | Roughly one to three years |
| Pipe concern | Cable can scrape fragile pipe | Old or fragile pipe should be inspected first |
The cost and duration figures come from HomeTips and Angi's 2025 data, where Angi puts the average hydro jetting job at about $475 within a typical $350 to $600 range, and snaking a sewer main at $100 to $400. Actual quotes vary with pipe length, access, the severity of the clog, and whether a camera inspection is included.
When snaking is the right call
- One sink, tub or toilet is slow and the rest of the house drains fine.
- The clog is new and you know the likely cause, such as hair or a foreign object.
- You want the lowest-priced way to get water moving today.
- The plumber needs to clear a path before a camera can go through.
Plumbers often snake first and recommend jetting only if the camera shows buildup left on the walls. Snaking is also the safer choice for a fragile pipe that has not been inspected. See the drain cleaning page for how a standard visit goes.
When jetting is worth it
- The same drain clogs every few months, even after snaking.
- A kitchen line is coated with grease, which is common in homes and in restaurants.
- Roots have entered joints in a main line, but the pipe is otherwise intact.
- Several fixtures back up together, pointing to a buildup along the main line rather than a single wad.
- You want maintenance cleaning on a pipe that is known to be sound.
The HomeTips comparison estimates that snaking two or three times a year can add up to about $800 to $1,000 or more, while a single jetting costs about $400 to $600. That is the reason a repeat clog is often less costly to solve with jetting than to keep snaking.
When not to jet
High pressure is not right for every pipe. Angi warns that the force can damage old pipes, and notes that PVC, a common sewer material, is considered safe. HomeTips advises inspecting older or fragile pipes first, often with a camera. Homes around Tampa that were built before 1980 may have cast iron under the slab or clay in the yard, and some of that pipe is cracked, offset or thin. If a camera shows a collapsed section or a break, jetting will not repair it and could make a weak spot worse. In that case the next conversation is about repair, which our guide on sewer line replacement and trenchless repair covers. A sewer camera inspection before any high-pressure work answers the question.
Local factors in Tampa Bay
Roots are a constant in a warm, wet climate with sandy soil, and they find any joint that leaks. Heavy summer rain and storm surge can overload drains and push water back up the line, which is a different problem from a clog. Hard water also leaves mineral scale. The City of Tampa reports average finished water hardness around 211 mg/L, or about 12.3 grains per gallon, and scale can narrow drain lines over many years, one reason a water softener helps pipes as well as appliances. Many homes have two cleanouts, one near the foundation and one at or near the property line, which gives a plumber a choice of where to start.
Restaurants and businesses
Kitchens that handle fat, oil and grease are the classic jetting customer, and the City of Tampa has a grease ordinance for food service businesses. If you run a kitchen, ask about a regular jetting schedule rather than waiting for a backup on a busy night. Details are on the commercial plumbing page.
What to expect on the day
For snaking, a plumber usually runs the machine through a cleanout or the fixture itself, and the visit is often short. For jetting, the plumber sets up a hose reel and a water source, feeds the nozzle down the line, and works back toward the cleanout while debris flows out. Water has to go somewhere, so expect some mess at the access point and let the plumber know about a low spot in the yard or a floor drain that backs up. Afterward, a follow-up camera pass shows whether roots, scale or a damaged section are still there. If a section is cracked or a root ball is wedged in a bad joint, cleaning only buys time, and the conversation turns to repair. Keep an eye on the drain over the next few weeks, because a clog that returns quickly points to a structural problem, not buildup.
What to ask before you book
- Will you camera the line before and after?
- Is the price for snaking or jetting, and what does it include?
- Is my pipe material safe for high pressure?
- If the clog returns, what does that tell us about the pipe?
You can verify a plumbing contractor on the DBPR "Verify a Licensee" page. Towns across the region, including Largo and Riverview, are served by the same referral line, and you can see every town on the service areas page. For general pricing, read how much a plumber costs in Tampa.
Frequently asked questions
Is hydro jetting better than snaking?
Can hydro jetting damage my pipes?
How often should a main line be jetted?
Sources
Last updated: