Shut off the water at the main valve, switch off power to any wet area if you can do it safely, open a faucet to drain the lines, and start moving belongings out of the water. Then call a plumber. What you do in the first ten minutes decides how much water gets into your walls and floors.
Minutes 0 to 2: stop the water
Find your main shut-off and turn it fully closed. In most Tampa homes the private shut-off sits between the utility's meter box at the property line and the house, though some homes have a second valve where the line enters the garage, a utility closet or the exterior wall. The City of Tampa owns the curb stop at the meter, and customers are not supposed to operate it. If you cannot close your own valve, or there is none, call the City of Tampa Utilities Call Center at (813) 274-8811 for a water emergency in the city, or your own water provider if you are in another town. See your water bill if you are not sure who that is.
Valves are either a round wheel handle, which you turn clockwise, or a lever that closes when it sits at a right angle to the pipe. A wheel valve that is stuck needs steady pressure, not a hammer. If a single fixture is the source, such as a toilet, sink or washing machine, its own angle stop may be enough, and closing it can be quicker than going outside to the main.
Minutes 2 to 4: think about electricity
Water and electricity are a poor combination. If water is falling through a ceiling, running down a wall with outlets, or pooling around appliances, turn off the breaker for that area. Only do this if the panel is dry and you can reach it without standing in water. If you cannot do it safely, stay out of the wet area and call the electric utility or an electrician. Do not touch light switches or plugged-in devices in standing water.
Gas is a separate concern. If the break is near a gas appliance and you smell gas, leave the home, call 911, then call Peoples Gas at 877-832-6747. Our gas smell guide covers what comes next.
Minutes 4 to 6: drain the system
With the main closed, open the lowest and the highest cold faucets and flush a toilet or two. That relieves pressure and lets the remaining water in the pipes drain out rather than keep leaking at the break. If the burst was on the hot side, turn off the water heater, or at least its gas control or breaker, so the elements or burner are not running with the tank starved of water. Electric elements can burn out dry. Our repair versus replacement guide explains what to do if the heater was affected.
Minutes 6 to 10: limit the damage
- Move rugs, electronics, paper and furniture away from the water. Lift furniture legs onto blocks or foil.
- Soak up what you can with towels, a mop, or a wet-dry vacuum rated for water. Do not use a standard household vacuum.
- Put a bucket under any active ceiling drip, and poke a small hole in a bulging ceiling to release trapped water in a controlled spot. Only do this if you can stand clear of the area below.
- Take photos and short videos of the source and the damage before cleanup. Insurance adjusters ask for them.
- Turn on fans and open windows only if humidity outdoors is lower than inside. In summer Tampa Bay air is often as damp as your wet drywall, so a dehumidifier does more.
Moisture is a bigger issue here than in cooler climates. Mold can start growing on wet materials in a day or two, and the EPA recommends drying wet materials within 24 to 48 hours. Waiting for a convenient time is not a good plan.
Calling a plumber
When you call, give the location of the break, whether the main is shut off, whether the leak is in a wall, ceiling or slab, and whether water is still flowing. If you suspect the leak is under the floor rather than in the wall, read our slab leak signs guide. For a burst pipe, the burst pipe repair page describes what the repair usually involves, and the emergency plumber page explains how an urgent call is handled. Our emergency or wait guide can help you judge urgency if the water is stopped.
Why pipes burst in Florida
Freezing is the best-known cause, and a hard freeze does hit Tampa Bay on rare nights, especially for exposed hose bibs, irrigation lines and attic or exterior pipes. But most bursts here have other causes: aging galvanized supply lines that corrode from the inside, polybutylene in some homes built from the 1980s to mid-1990s, high water pressure, a failed fitting, tree roots or ground movement, and impact damage from construction or digging. About 44 percent of City of Tampa homes were built before 1980, including older stock in Ybor City, Hyde Park and Seminole Heights, so old materials are common. If your pipes are old and have failed once, ask a plumber about the repiping page options instead of patching repeatedly.
What repair may cost
One national cost guide from 2025 puts the average burst pipe repair around $500, with most jobs between $200 and $3,000 and labor making up most of the bill. The same guide lists main line repairs averaging about $1,080 and sewer repairs averaging $2,250. Emergency call-outs can add $100 to $300. Those are national figures, not Tampa quotes, and they do not include drying out walls, replacing drywall or flooring, or mold work, which can add up quickly. Ask for a written price, a description of the repair and whether access holes in drywall will be patched. Our plumber cost guide covers how pricing works locally.
Insurance and what to document
Many homeowner policies cover sudden and accidental water damage from a burst pipe but not slow leaks or neglected maintenance. The NAIC notes that coverage depends on the policy and that you are expected to take reasonable steps to prevent further damage, which is another reason the first ten minutes matter. Keep the damaged section of pipe if the plumber removes it, keep receipts, and notify your insurer promptly. Ask the adjuster whether you need to get a mitigation company in before the walls are opened.
Common mistakes in the first minutes
People tend to lose time in predictable ways. They search for the valve while water keeps running, they try to patch the pipe before the water is off, or they leave wet drywall to dry on its own. Another common mistake is turning the water back on to test a temporary fix before the line has drained and been checked, which can undo the repair and flood the same room twice. A pipe repair clamp or push-fit coupling can be a reasonable stopgap, but treat it as temporary and have a plumber confirm the fix. If you are not sure the leak is stopped, leave the main off and wait for help.
After the repair
Once the plumber has repaired the break, restore water slowly, check every fixture, and watch the water meter with everything off. If it keeps moving, there is another leak. Have the plumber look at your pressure regulator if the burst was caused by pressure. In the days after, check walls, ceilings and baseboards for staining or soft spots. Households in Brandon, Riverview and across the service area can use the same steps, and our service list shows related work.
Frequently asked questions
Where is my main water shut-off in a Tampa home?
Should I turn off the water heater after a pipe bursts?
Will insurance pay for a burst pipe?
Sources
Last updated: